Hi all.
I have an Asus P5WDG2-WS-Pro, and am having trouble trying to install a
version of Ubuntu I got from the last WLUG install meet - (This is the
Feisty 7.04 Alternative CD I believe - will need to double-check this).
Basically it boots from CD fine, but fails to recognise the CD-ROM drive
- is it not recognising the IDE controller?
I will try to sort out a dmesg from when I boot the 7.04 CD.
The strange thing is that Dapper 6.06 Live CD boots from same CD-ROM,
and happily installs from the same CD-ROM - any recommendations on
things to try?
Mobo chipset info:
North Bridge:
Intel 975x
South Bridge:
Intel ICH7R
PCI-X:
6702PXH
DMESG Stuff:
Linux version 2.6.15-28-686 (buildd(a)terranova) (gcc version 4.0.3
(Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Thu May 10 09:56:30 UTC 2007
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 233
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: probing with STATUS(0x50) instead of ALTSTATUS(0x0a)
hda: probing with STATUS(0x51) instead of ALTSTATUS(0x0a)
hda: probing with STATUS(0x51) instead of ALTSTATUS(0x0a)
hda: LITE-ON DVDRW SOHW-1693S, ATAPI CD/DVD-ROM drive
hdb: probing with STATUS(0x00) instead of ALTSTATUS(0x0a)
hdb: probing with STATUS(0x00) instead of ALTSTATUS(0x0a)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ACPI: bus type scsi registered
libata version 1.20 loaded.
ahci 0000:00:1f.2: version 1.2
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
ata1: SATA max UDMA/133 cmd 0xF8876900 ctl 0x0 bmdma 0x0 irq 58
ata2: SATA max UDMA/133 cmd 0xF8876980 ctl 0x0 bmdma 0x0 irq 58
ata3: SATA max UDMA/133 cmd 0xF8876A00 ctl 0x0 bmdma 0x0 irq 58
ata4: SATA max UDMA/133 cmd 0xF8876A80 ctl 0x0 bmdma 0x0 irq 58
ata1: dev 0 cfg 00:0c5a 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01
87:4023 88:207f 93:0000
ata1: dev 0 ATA-7, max UDMA/133, 625142448 sectors: LBA48
sata_get_dev_handle: SATA dev addr=0x1f0002, handle=0xdffe5d80
ata1: dev 0 configured for UDMA/133
sata_get_dev_handle: SATA dev addr=0x1f0002, handle=0xdffe5d80
scsi1 : ahci
ata2: no device found (phy stat 00000000)
scsi2 : ahci
ata3: dev 0 cfg 00:0c5a 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01
87:4023 88:207f 93:0000
ata3: dev 0 ATA-7, max UDMA/133, 625142448 sectors: LBA48
sata_get_dev_handle: SATA dev addr=0x1f0002, handle=0xdffe5d80
ata3: dev 0 configured for UDMA/133
sata_get_dev_handle: SATA dev addr=0x1f0002, handle=0xdffe5d80
scsi3 : ahci
ata4: no device found (phy stat 00000000)
scsi4 : ahci
Vendor: ATA Model: ST3320620AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: ST3320620AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
Driver 'sd' needs updating - please use bus_type methods
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 > sda4
sd 1:0:0:0: Attached scsi disk sda
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3
sd 3:0:0:0: Attached scsi disk sdb
Probing IDE interface ide1...
Cheers,
Elroy.